I recently purchased a 23cm transverter from SG-lab. It’s a 145MHz IF with a L.O. frequency of 1152MHz (default; can be changed). Output power is 2w. Tonight, I had my first QSO on the 23cm band with it with two friends who both have the same transverter, G7UVW and M1GEO. I used a Yaesu VX-6 for the IF, but that went flat, so I switched to the Icom ID-51, which is set to record all QSO’s, so there is an MP3 below!
The transverter comes with a HB9CV antenna etched on a PCB which works really well. I had the ID-51 in one hand and the antenna in the other, holding it out the window. All three of us had the same setup holding the antenna out of or near a window. I first spoke to David G7UVW at 2.2 miles and then George M1GEO at 1.2 miles. Signals were good all round, although it seems the best signal between G7UVW and I was via reflecting off a school building opposite me (or something, the peak signal certainly wasn’t in his direction!).
We are all very happy with the result. I am now going to build a couple of Yagi antennas, look at getting a PA and try out some of the 1.3GHz UK Activity Contests in the summer.
My first couple of 23cm QSO’s using a 2w transverter and a handheld.
The setup of George M1GEO with the HB9CV on a broom stick boom!
Update: The next day, George M1GEO took his transverter up to the 12th floor at UCL in central London. We made contact easily again both with 2w and a HB9CV antenna, over a distance of 14km.
Icom don’t seem to like N-Type connectors. I have an X-50N Co-linear, with about 5 metres of Westflex 103 of which both ends are terminated with an N-Type plug. I used to have the Yaesu FT-897D, which is why I have the N-Type attached for VHF and UHF. Yaesu (at least in Europe) use N-Type chassis sockets for their UHF transceivers, but Icom use the SO-239, unless you buy something like the IC-9100. Since buying the IC-7100, I have been using an adapter.
Today, I decided to change the chassis socket on the Icom to an N-Type. Conveniently, there is no soldering involved. They have used a sprung clip to connect to the socket pin. Perhaps this helps prevent connection problems due to thermal expansion and contraction between the chassis and PCB or any movement in the connector pin itself. You could probably change it without opening the case, but its nice to see what you are doing and to know you are not bending the clip! Below shows the internal socket connections.
Icom IC-7100 RF Connectors
Icom IC-7100 N-Type fitted for VHF / UHF
Before changing the socket, SWR was around 1.5:1 at 433MHz with the original SO-239 and PL-259 to N-Type adapter. After changing the socket to a plain N-Type and removing the adapter, SWR is 1.1:1 or better from 430-440MHz (Shown by the transceiver). It shows how critical things like connectors and adapters get at UHF, although most of the miss-match was probably the adapter. It also makes it easy to remember which port is HF and which is VHF/UHF. A mod well done. If only Icom built them with N-Type sockets in the first place! Oh, and whilst I had the lid off, here is a photo of the inside of the IC-7100 🙂
1:1 SWR after changing the chassis SO-239 to an N-Type socket
I recently took my power supply apart to give it a clean and replace the fan with something quieter. I have used this supply for a few years and its been good and reliable, so I decided to add a reviews section to the website, starting with my experience using this power supply.
A few of us decided to have a go in the RSGB 21/28MHz contest on Sunday. We used Georges call, M1GEO and a combination of equipment from us all. I brought my 3 element 28MHz Yagi, Dave M0TAZ brought the two masts and his 21MHz 4 element Yagi, while George and his dad brought the Icom IC-7700 and generator. Fred G3SVK also came and done some CW.
UK stations can only work outside the UK and non UK stations can only work UK stations. This made it quite hard work as there was not much activity due to the bands not being in good shape, especially 10m. We could hear some beacons though, although not strong, we received a beacon in Brazil and one in Argentina. We did work some good DX however, including South Africa, Uruguay, Brazil and VP8NO in the Falkland Islands on 28MHz.
The operating table.
Still, we had fun operating outside in the October sunshine for possibly the last time this year!
We had a fun day up at Kelvedon Hatch on Sunday for the Practical Wireless 70MHz contest with fantastic weather yet again!
Dave M0TAZ was operating with his Racal PU12 mast and IC-7100 and I brought along my amplifier and Yagi for this once a year event. There was good activity although as predicted, the final hour was a bit slow going.
We were operating for the whole four hours, running 160W into an 8.24dB Yagi giving an ERP of ~1kW and we worked a total of 47 stations, of which the best DX was GM4JR at 454km. We also worked into Wales and The Netherlands.
As PW contests do not give you a QSO map, I plotted my own in Google Maps by exporting a KML file from the Minos logging software. The QSO map can be seen here.
A photo of the field can be seen below…
PW 70MHz Contest 2015 at Kelvedon Hatch
I also took some video on my phone, which can be seen below…
You can also read Dave’s article on his website. George M1GEO, Chris G8OCV, Dave M0YOL and some others also attended to play some radio so it was a good day all round!
We had some great September weather today for the 2nd 70MHz contest. We setup at the Kelvedon Hatch ‘Secret Nuclear Bunker’ as seen above, using my new 70MHz amplifier at 160w and my 4 element DK7ZB 12.5Ω Yagi.
Conditions seemed quite normal, we worked no Scotland or Ireland but our best DX (as many others) was PA4VHF at 449km. Other highlights were GJ3YHU in Jersey and M1CJN/P in the North York Moors. Total contacts was 46.
A very enjoyable day of operating and testing the new amplifier. Next week, it’s the Practical Wireless 70MHz contest, so lets hope for the same weather and some band openings perhaps? Maybe I’m asking too much 🙂
The Claimed Scores are available. Thanks to Dave M0TAZ, George M1GEO, Dave M0YOL and Chris G8OCV for help & company, and of course everyone we worked (or tried to work!).
Today, I finished a project I started over two years ago. It’s not that it took two years to build, it’s just that its taken me two years to get the parts together and build in my spare time! The upcoming 2nd 70MHz contest and PW 70MHz contest prompted me to get this finished.
Its a 300w 70MHz amplifier, using a BLF 278 MOSFET. Power supply is 50v @ 10A. The amplifier has 9dB attenuation at the PA input to bring the gain down to something usable, as without the attenuation, 2.5w input gives 300w output (21dB gain)! The input & output power, with 9dB ATT (total 12dB gain) is:
5w = 100w
7.5w = 150w
10w = 200w
15w = 300w
The amplifier uses ~7.5a @ 48v for 200w O/P, so it’s around 80% efficient. Bias is set to 750mA. The maximum power here in the UK on 70MHz is 160w, for which this amplifier requires 8w of input. Below is a picture of the inside. I will tidy up the cables at some point!
300w PA & LPF
I need a larger Bird element to measure the 300w output on the Bird 43!
On Sunday, Dave and I went to South Weald to take part in the 144MHz Backpackers Contest. We used Dave’s 9 element Tonna 6m AGL and 10w from the Icom IC-7100. The weather was perfect, blue skies and sunshine and hardly a breeze! Dave worked 51 stations and some good DX for low power, due to the big stations competing in the 144MHz Trophy contest. We managed contacts with England, Wales, Scotland, France, Germany, Belgium and The Netherlands. Our best DX was DR4X at 648 KM. The QSO map can be seen below.
5th Backpackers 2015 QSO map
I brought along some 70MHz equipment, which I set up after packing away the 144MHz gear and spent about an hour on 4m working 8 stations. All in all, a good days operating in the sun!